Not every slowdown is a Wi-Fi problem

When employees complain that “the internet is slow,” the first instinct is to blame the wireless network. Sometimes that is right, but before replacing equipment it is worth checking what sits in front of it: the internet line itself, the router or firewall, the switch that the access points connect to, and sometimes a single computer that loads the whole line by uploading a backup or downloading a large update.

A simple test helps narrow it down. If a computer connected by cable is also slow, the problem is probably not the Wi-Fi. If the slowness appears only in certain rooms, it is usually a coverage issue. If it is tied to peak hours or large meetings, the problem is probably capacity or the line’s bandwidth. And if only certain devices suffer, check them and their drivers before touching the network.

This order saves money and time. New access points will not help an overloaded internet line, and upgrading the line will not help a room the signal does not reach.

Access point placement and count

The most common mistake is a single “powerful” router at one end of the office that is supposed to cover the whole space. Concrete walls, a reinforced safe room, metal cabinets and glass weaken the signal considerably, and what works next to the router fades by the third room. Turning up transmit power does not solve this, because employees’ devices transmit back at much lower power, and the router simply cannot hear them.

The solution is several access points, usually on the ceiling and in the center of the areas where people work, with power tuned so they overlap without interfering with each other. You also need to think about capacity, meaning how many devices connect to each point at the same time. Good coverage in an empty room says little about a full meeting room where every participant has a laptop and a phone.

In large or complex offices, it is worth doing a wireless site survey before installation, so access points are placed based on measurement rather than guesswork. After moving offices or changing the room layout, it is also worth checking again.

Bands, channels and interference

Wi-Fi networks run on several frequency bands. The 2.4GHz band reaches farther, but it is crowded and sensitive to interference, especially in an office building where every neighbor broadcasts its own network. The 5GHz band offers more channels and higher speed over a shorter range, and newer equipment also has the 6GHz band, which is still less crowded. As a rule, it is better to connect employees’ computers and phones to 5GHz or 6GHz, and leave 2.4GHz for older devices that need it.

Professional equipment can choose channels and power automatically based on the environment (Radio Resource Management). Home equipment, which is often installed in offices too, leaves everything at factory settings, and two nearby access points on the same channel slow each other down. A channel width that is too wide in a crowded environment can also do more harm than good.

The standard matters too. Wi-Fi 6 and Wi-Fi 6E equipment is common today in professional access points, and Wi-Fi 7 is already available. Their advantage is felt mainly in crowded environments, provided the computers and phones support the standard. There is no point upgrading the access points while leaving old network adapters in the computers that limit the speed.

The infrastructure behind the airwaves

A good wireless network relies on a good wired network. Every access point needs a working network cable that runs to a switch, preferably a switch that also powers it through the cable (PoE). Mesh systems, in which the access points communicate with each other over the air, are convenient where a cable cannot be run, but every wireless hop uses up part of the bandwidth.

It is worth checking the less glamorous things too: the network cabinet, old or damaged cables, an old switch that limits speed, and wall jacks nobody knows where they lead. Documenting the infrastructure, what is connected to what and which equipment is where, saves hours in every future fault.

Guest network and separate networks

A single network that everyone connects to, employees, guests, the meeting room TV and the security cameras, is convenient. It also lets every device reach the business’s servers and computers. A guest’s device infected with malware, or a camera with old firmware, becomes an entry point to the entire network.

The accepted solution is dividing the network into separate segments (network segmentation) using VLANs, with the firewall deciding what may pass between them:

  • Employee network: access to business systems, for authorized devices only.
  • Guest network: internet access only, with the connected devices isolated from each other (client isolation).
  • Device network: cameras, printers, displays and smart devices (IoT), with access only to what they need.
  • Management network: for the management interfaces of the switches, access points and firewall.

This is also a layer of protection against ransomware and leaks: even if one device is breached, the separation limits what the attacker can reach (lateral movement).

Securing the wireless network

The wireless network extends beyond the office walls, into the stairwell, the parking lot and the neighboring office. That makes its settings part of the business’s information security, not just a technical matter.

  • Current encryption: WPA3 where the equipment supports it, and at least WPA2 with a long password.
  • Individual sign-in for employees: in organizations with Active Directory or Entra ID, the employee network can be tied to individual authentication (Enterprise), so an employee who leaves loses access the moment their user account is closed.
  • Protected management interfaces: the factory password is replaced, and management is not reachable from the guest network or the internet.
  • Firmware updates: for the access points, the router and the firewall, just like any computer.

Central management and monitoring

In an office with more than one access point, central management (a controller) makes a big difference. From one place you can see which points are active, how many devices are connected to each, where there is interference and when a point went down. You can update firmware on all of them at once and change settings without walking from room to room.

Monitoring turns the work from reactive to preventive. Instead of waiting for an employee to complain, the IT provider gets an alert when an access point disconnects or a switch starts showing errors, and deals with it before the problem is felt. The same monitoring also makes it possible to spot an unknown device that has connected to the network (rogue device).

A practical order of checks

  1. Check whether the slowness also exists on a wired connection, and if so, start with the line and the router.
  2. Map where and when there is a problem: rooms, hours and devices.
  3. Review the placement and number of access points, and the capacity in crowded areas.
  4. Make sure every access point is connected by a working cable to a suitable switch.
  5. Separate the employee, guest and device networks (network segmentation).
  6. Update encryption, passwords and firmware.
  7. Move the network to central management and monitoring.

A stable network is infrastructure that all the work in the office relies on, and an unsecured network is a door to everything behind it. Whoever designs it should see both sides, and understand information security no less than frequencies.